Questa è la procedura consigliata sul forum xda per ottenere i permessi root, se qualcuno la traduce ne sarei molto grato. Grazie1. Flash your tab with GB_Stock_Safe_v5 (thanks Overcome team for the stock safe ROM link)..use the pit file and modem file abailable
I do this for a clean and fresh install on my tab
2. Just let it boot and complete the setup wizard as necessary..
3. Boot again to download mode
4. Flash the JQ8 room as PDA and re-partition enabled (thicked)..dont need pit file and modem file..just let it blank!
5. Let it boot again till completed..and then boot again to download mode
6. Flash overcome kernel v4 as PDA without re_partition (unthicked)..thanks overcome team (you can use v3 if its more suitable for you)
7. Now let it boot completely..just listen the sexy voice
8. After completely booted..in settings-application..thick the "unknown source" option..and usb debuging mode activated..
9. After that..go to the link that j@cks provided as on above quoted post..
Download the GT-I9000v102.7z file, and also runme.zip file as also uploaded by j@cks above..thanks to him
10. Extract both files
11. Connect you tab to your PC..
Attention..make sure you have samsung usb driver installed on you PC!
12. On GT-I9000v102 folder..replace the runme bat with the one that j@cks provided..and run the runme.bat
13. Wait...this will takes time..let the process running..
14. Here is what hapen with me..on step 6 my tab got freezed/blank..just disconnect it from PC (dont close the runme..just disconnect it)
Press on the power button until its rebooted..
15. Connect again, and let the process continued..
It will then rebooted..and you will notice the the power on sound and samsung boot animation aren't exist anymore..you could always follow the thread where you download the rooting tools to get it back..
Congratulations..your tab are rooted..!
Originariamente inviato da Guildamx
Mitico guildmx. Eseguito e funziona. Ho aggiornato anche su
Inviato dal mio GT-P1000 usando Androidiani App
Ultima modifica di lupoalba; 14-12-11 alle 13:16
si puo tradurre facilmente, ma e' proprio quella che ho provato, inserendo il kernel della overcome 4 che dovrebbe andare ancora meglio visto che usa l'ext4, ma il root non va, benche il tool (che agisce tramite ADB) dica che sia a posto...almeno sul mio che cmq pare veramente ostico.
Cmq:
1)torna alla stock gbsafe v5
2) esegui il wizard di primo avvio
3) riparti in download
4)flasha la jq8 (2.3.6) con repartition abilitato senza pit file
5) riesegui il wizad di prima accensione (a me qui non funziona la tastiera in genere)
6) riparti in download e flasha il kernel overcome 4v ( anche il v3 va bene)
7) fai eseguire il boot con la conversione del filesystem
8) abilita "fonti conosciute e usb debug"
9) scarica il file fornito da j@cks de post precedente
10) scompatta il file
11) connetti il tab acceso (in modalita normale, non download o recovery)
12) nella cartella dove hai decompresso i files sostituisci runme.bat con quello fornito da j@cks ed esegui runme.bat
13) aspetta che il processo sia completo (a me ci impiegava 3 minuti circa)
14) se il tab si blocca e non risponde (come e' accaduto all'autore della guida e anche a me) stacca il tab e spegnilo forzatamente premento il tasto d'accensione per circa 10 secondi e poi riaccendilo
15)connettilo e vedrai che il processo continua
adesso ha il root, uno dei sintomi e' che il suono e il logo di accensione non ci sono piu.
OnePlus One
crDroid 5.5 (Android 4.4)
Samsung Note 8.0
CivZ-FLEXNOTE-8.0-REV2.1 (Android 4.4)
"In un periodo di tempo sufficientemente ampio, tutti i PC monteranno Linux e tutti gli smartphone Android"
(Benedict Neuhaus, futurologo)
finalmente