Si ho il kernel elemental... Dove devo andare per cambiare le impostazioni??
Visualizzazione stampabile
Quote:
NOTES:
Configuration
Your choices in the Aroma installer are used to build a configuration file. The config file is located at /etc/elementalx.conf. You can edit this file to change kernel settings. Whatever is set in this file will take effect when the device is booted (unless other scripts or apps interfere!)
The settings can be changed by editing /etc/elementalx.conf and rebooting. Advanced users can apply settings on the fly by running /etc/init.d/99elementalx as root.
There is no need to edit /etc/init.d/99elementalx. All settings are configured in /etc/elementalx.conf.
If settings are not sticking, make sure the file permissions for /etc/init.d/99elementalx are set to execute. Every time the settings are applied, a log file is created at /data/local/tmp/elementalx-kernel.log. Problems can be diagnosed by looking at the log file.
Please check to see if any /etc/init.d scripts or apps are interfering with your settings If you're on ViperXL, make sure your settings in Venom Tweaks are the same as the ones in /etc/elementalx.conf (for example, sweep2wake settings)
Sweep2Wake
Sweep2wake allows you to wake up your device by swiping your finger across the capacitive buttons from left to right. Swiping from right to left will put it back to sleep (sweep2sleep). There are now options for sweep2wake/sweep2sleep, sweep2sleep only, and disabled. If you use ViperXL, make sure to enable sweep2wake in Venom Tweaks. Note that in Venom Tweaks, the sweep2sleep only option can be selected by choosing Enable (no buttons backlight).
DoubleTap2Wake
DoubleTap2Wake (DT2W) allows you to wake the device by double tapping the capacitive buttons.
/sys/android_key/doubletap2wake
0=disabled
1=enable doubletap2wake using back button
2=enable doubletap2wake using home button
3=enable doubletap2wake using recent apps button
Button Light Notification
With Button Light Notification (BLN), the capacitive buttons will blink on and off when you have a new notification. You can edit /etc/elementalx.conf to change the setting on boot.
/sys/class/leds/button-backlight/bln
0 = disabled
1 = BLN enabled
Il tuo problema dovrebbe essere il DoubleTap2Wake, ma potrebbe dipendere anche dallo Sweep2Wak se non li usi puoi disabilitarli entrambi, se non ti riesce, forse conviene riflashare il kernel, e disabiltarli in fase di installazione !!!
infatti se hai flashato tramite FlashImageGUI ... giustamente è impostato tutto come da defoult, ed i files da editare non sono presenti ... ora da Recovery flasha il file zip dell'ElementalX
e durante l'installazione stai attenta a scegliere di Disabilitare le Funzioni DoubleTap2Wake ed Sweep2Wak
mi pare che in automatico non funzionerà nemmeno il Button Light Notification
EDIT: per tutti coloro che hanno il terminale in S-ON
la procedura per installare un Kernel come ElementalX o Bulletproff
è identica all'installazione di una nuova ROM
e prevede il Flash del boot.img da Fastboot o FlashImageGUI
più il Flash dello zip da Recovery.
si da Recovery ...
per ElementalX dal Flash parte Aroma Installer è mi pare che faccia Wipe in automatico, e te lo chiederà anche alla fine
tu comunque fai Wipe Cache e Dalvik Cache da recovery, prima ed anche alla fine, ho provato personalmente non gli fà male !!!!
PS. ho aggiunto un EDIT al Post precedente !!!!
Se vuoi anche il BLN funzionante attiva almeno il DoubleTap2wake
sinceramente non ho problemi di nessun tipo ora con questa rom :)