Scusate.... ma se facevate un Hard Reset non si riusciva a risolvere senza assistenza??
Scusate.... ma se facevate un Hard Reset non si riusciva a risolvere senza assistenza??
La procedura per ripristinare il tablet dal brick è la seguente, funziona solo su linux, scritta da setialpha di ArcTablet
- unpack zip file
- download unpack-bootimg.pl (http://files.coralic.nl/system/ to boot.img-ramdisk/
- cd boot.img-ramdisk/ && find . | cpio -o -H newc | gzip > ../newramdisk.cpio.gz && cd ..
- boot with those files: fastboot boot boot.img-kernel.gz newramdisk.cpio.gz
- only if google apps are installed: when the choose-an-app-for-action pop-up appears, quickly choose one, before the pop-up disappears and follow the instructions of the start-up-wizard (if google-apps are installed there are two wizards then, this will give faulty results when doing factory reset or similar things)
- simply follow instructions of start-up-wizard (after doing a factory reset, the start-up-wizard might be the point the system boot hangs)
- reboot tablet (it should work now)
tanto per capirci.....
tu hai preso il tablet.... lo hai collegato al pc... lo hai acceso con il tasto volume + premuto....
con il tablet a schermo nero.... hai aperto una shell su windows come amministratore....
da questa shell hai digitato ADB SHELL
poi
SU
poi
REBOOT RECOVERY
e il tablet è rimasto invariato con il suo bel errore?
se si, ok, scusa non rompo più.
se no, sarebbe una bella prova da fare.
Ultima modifica di Alex9000; 23-01-12 alle 23:33
il tablet dopo il ripristino resta fermo sul boot.
si può fare solo reset power + giù
in adb non va perchè si sputtanano i permessi in scrittura su system e il tablet non si accende di conseguenza va solo in fastboot.
da fastboot non si può flashare perchè non si hanno i permessi ripeto di nuovo che non si risolve da recovery e l'unico modo è quello descritto da me sopra!
Questo tizio ci è riuscito...
in questa pagina: http://www.arctablet.com/blog/forum/...al-rom-backup/.I managed to unbrick my device (wooooooooo!).
This is how I did it (lots of trial and error, may not apply to your device!) – quick and dirty write, don't argue about interpuctuation and layout :
Download the rom backup from the first post (didn't get the chance to test finnless' as I unbricked right before)
unpack the zip-file, you'll see another zip-file, unpack, too.
get unpack-bootimg.pl (http://files.coralic.nl/unpack…..bootimg.pl)
use the .pl file to unpack the boot.img (you'll now have: boot.img-kernel.gz and boot.img-ramdisk
copy all files from the system folder into boot.img-ramdisk/system (override if necessary)
re-build the ramdisk with (attention linux-command!): cd boot.img-ramdisk && find . | cpio -o -H newc | gzip > ../newramdisk.cpio.gz && cd ..
now put tablet in fastboot mode: Power-up+Volume (keys will flash, wait until "unflash").
connect tablet to pc (note: if in endless boot-loop, disconnect from any cable first, hit reset and then put tablet into fastboot mode (pressing reset while connected to power-plug or pc will result in entering qualcomm programming mode!))
issue: fastboot boot boot.img-kernel.gz newramdisk.cpio.gz
tablet will flash the stuff and boot automatically. It will tell you something like "safe mode" in lower left corner.
NOW the important part! the screen will flicker with a selection screen known, then having more than one browser (or similar) quickly press the one of them (trial and erorr), so that the startup wizard launches, go through the wizard (may be done more than one time) tablet will when work.
If phone never exits safe mode re-flash unmodified boot.img: fastboot flash boot boot.img
and to the step with the startup wizard again (that was the point there mine started working again).
Don't blame me for this beeing stupid, but it worked for me
Ma io sinceramente unav olta che premo volume e power oltre a lampeggiare una volta non succede un bel niente ç_ç
e fatto ciò cosa dovrei fare? °-°