debugging is on, but get the same message.
When you download the recovery, and you unpack it you get a .img file, the .img file you dont need to extract the files right???
debugging is on, but get the same message.
When you download the recovery, and you unpack it you get a .img file, the .img file you dont need to extract the files right???
Ultima modifica di theduke1989; 13-05-15 alle 08:35
Hi, first of all you have to install drivers and fastboot/adb tools from the second post
After you have installed them, you have to connect your smartphone to PC and let the PC recognize the cell. After the drivers are been installed you have to reboot into fastboot mode (from Settings -> About phone -> System update -> Fastboot and then confirm the warning message).
When you are in fastboot mode, PC will install again another kind of driver (if not you haven't installed the driver I told before) you can type the command you have said in your post.
theduke1989 (13-05-15)
great did install now the adb tool , did not do this before.
Uhm now i am in fastboot mode with the phone connected to the pc but the pc dident install anykind of driver.
I think i have installed already drivers for the ZTE NUBIA Z9 before for other roms, so now again when i am in cmd and want to run fastboot -i 0x19d2 flash recovery Recovery_TWRP.img i get the same message as before.
Have debugging on, did everything you told, but stuck at this point: fastboot -i 0x19d2 flash recovery Recovery_TWRP.img
Close every Command Prompt you have opened and then install again ADB/Fastboot tools... when installing tools you have to press Y to every question it asks...
After everything is installed, open a Command Prompt and type the command fastboot if it shows this is correctly installed:
codice:C:\Users\unknown>fastboot usage: fastboot [ <option> ] <command> commands: update <filename> reflash device from update.zip flashall flash boot, system, vendor and if fo nd, recovery flash <partition> [ <filename> ] write a file to a flash partition erase <partition> erase a flash partition format[:[<fs type>][:[<size>]] <partition> format a flash partition. Can override the fs type and/or size the bootloader reports. getvar <variable> display a bootloader variable boot <kernel> [ <ramdisk> [ <second> ] ] download and boot kernel flash:raw boot <kernel> [ <ramdisk> [ <second> ] ] create bootimage and flash it devices list all connected devices continue continue with autoboot reboot reboot device normally reboot-bootloader reboot device into bootloader help show this help message options: -w erase userdata and cache (and format if supported by partition type) -u do not first erase partition before formatting -s <specific device> specify device serial number or path to device port -l with "devices", lists device paths -p <product> specify product name -c <cmdline> override kernel commandline -i <vendor id> specify a custom USB vendor id -b <base_addr> specify a custom kernel base address default: 0x10000000 -n <page size> specify the nand page size. default: 2048 -S <size>[K|M|G] automatically sparse files greater than size. 0 to disable
theduke1989 (13-05-15)
thanks,
i saw on abd1.4.2 that there were no files copied, so i used 1 older, and than there were 4 files copied.
Did again use the commands, and now i get this:
so everything is ok?Microsoft Windows [Version 6.3.9600]
(c) 2013 Microsoft Corporation. Alle rechten voorbehouden.
C:\Users\>cd..
C:\Users>cd
C:\Users>cd desktop
C:\Users\\Desktop>cd test
C:\Users\\Desktop\test>fastboot -i 0x19d2 flash recovery Recovery
_TWRP.img
target reported max download size of 268435456 bytes
sending 'recovery' (24204 KB)...
OKAY [ 0.766s]
writing 'recovery'...
OKAY [ 0.703s]
finished. total time: 1.469s
C:\Users\\Desktop\test>fastboot -i 0x19d2 Recovery_TWRP.img
usage: fastboot [ <option> ] <command>
commands:
update <filename> reflash device from update.zip
flashall flash boot + recovery + system
flash <partition> [ <filename> ] write a file to a flash partition
erase <partition> erase a flash partition
format <partition> format a flash partition
getvar <variable> display a bootloader variable
boot <kernel> [ <ramdisk> ] download and boot kernel
flash:raw boot <kernel> [ <ramdisk> ] create bootimage and flash it
devices list all connected devices
continue continue with autoboot
reboot reboot device normally
reboot-bootloader reboot device into bootloader
help show this help message
options:
-w erase userdata and cache (and format
if supported by partition type)
-u do not first erase partition before
formatting
-s <specific device> specify device serial number
or path to device port
-l with "devices", lists device paths
-p <product> specify product name
-c <cmdline> override kernel commandline
-i <vendor id> specify a custom USB vendor id
-b <base_addr> specify a custom kernel base address.
default: 0x10000000
-n <page size> specify the nand page size. default:
2048
-S <size>[K|M|G] automatically sparse files greater th
an
size. 0 to disable
C:\Users\\Desktop\test>
but nothing happend on the phone, can i now jusr reboot system now or???? what next???
Ultima modifica di theduke1989; 13-05-15 alle 10:25
These are the commands to flash and then boot into twrp:
fastboot.exe -i 0x19d2 oem unlock
fastboot.exe -i 0x19d2 flash recovery recovery_twrp.img
fastboot.exe -i 0x19d2 boot recovery_twrp.img
@INNOR hai installato i driver del dispositivo? Lancia il comando e mentre sei in attesa del device, premi vol + (+) power per entrare in bootloader, poi collega il cavo usb al telefono
thanks, my phone did go to the twrp in my theme, but after rebooting again for twrp, it is in chinese (yirom.com things.).
do i must do this everytime with cmd or ????
my phones stucks at the red/white chinees letters, my phone doesen go further than that...
and recovery doesent work eather, the phone when you press vol- and power the phone restarts, but no recovery or fastboot...
Ultima modifica di theduke1989; 13-05-15 alle 13:29
Ciao a tutti,
questa mattina mi è arrivato il telefono, l'ho già rootato e installato il FW di Cuoco92 (Grazie mille per il lavoro), solo che ora mi dice che trova un aggiornamento disponibile? Inoltre se ci saranno aggiornamenti futuri dalla casa madre come si fà?
Tra l'altro, qualcuno ha sbloccato la banda LTE B20 800Mhz? Io ho Wind per cui niente LTE al momento
Vivi ogni giorno come se fosse l'ultimo...